Recycling, Volume 9, Issue 3 (June 2024) – 10 articles

The importance of environmental consciousness and sustainability is increasing among transportation governing bodies worldwide. Many government bodies are concerned with maximizing the usage of recycled substances in road construction. Therefore, assessing the effect of recycled materials consumption is essential, mainly when designing new ‘green’ pavement types. The primary objective of this study is to investigate the impact of different treatments on improving the interfacial transition zone (ITZ) of coarse recycled concrete aggregate (CRCA) and its application in asphalt mixes. Such an aim is accomplished by enhancing its physical and mechanical characteristics, as well as its microstructure. The surface morphology, chemical composition, and intermix phases of the ITZ area and calcium silicate hydrate (CSH) compounds for CRCA were evaluated using scanning electron microscopy (SEM), an energy-dispersive X-ray analyzer (EDAX), and X-ray diffraction analysis (XRD). The performance of asphalt mixtures that included treated and untreated CRCA was also examined using different tests. It was found that heat treatment is an effective technique for enhancing the ITZ. However, cracks were seen in the mortar of CRCA when exposed to high temperatures (500 °C), which adversely affects the characteristics of the mortar. Acid treatment appeared to be an effective approach for improving the ITZ area. Nevertheless, the treatment that used acetic acid, a weak acid, was more effective than HCl acid, a strong acid. The outcomes revealed that the ITZ microstructure is significantly enhanced under different treatment types; however, microstructure improvements mainly included increased surface homogeneity and CSH compounds and a reduced Ca/Si ratio. It was also found that the asphalt mixtures with different proportions of untreated CRCA exhibited enhanced resistance to rutting. Furthermore, their tensile strength ratio (TSR) values were above the minimal level requirements. Moreover, the asphalt mixture with 30% CRCA, which was treated with various treatment methods, demonstrated a significant improvement in the mixtures’ mechanical properties; therefore, its application is highly successful and an environmentally friendly solution. Full article

Valorizing food waste (FW) in sub-Saharan Africa (SSA) can enhance the efficiency of limited resources, make healthy diets more affordable, and foster the creation of innovative enterprises. The vast quantities of FW from the agri-food chain significantly threaten food security. To address this issue and maximize potential environmental and socio-economic benefits, valorizing waste, a value-adding process for waste materials, has emerged as a sustainable and efficient strategy. Valorizing FW reduces greenhouse gas emissions, mitigates climate change, enhances resource efficiency, and improves planetary health. As a pivotal player in the transition toward the circular economy, this study investigates the potential of converting FW into value-added products, offering entrepreneurial opportunities for SSA’s unemployed youth. A systematic literature review is conducted to identify and filter relevant articles over five years by applying inclusion and exclusion criteria. A total of 33 articles were included for in-depth analysis to address the study’s aim. The findings highlight a range of value-added products derived from FW, including renewable energy sources, nutraceuticals, and heavy metal adsorbents. These products present promising entrepreneurial prospects within SSA. Nonetheless, overcoming barriers to FW valorization adoption is crucial for fully realizing its potential as a profitable business avenue. Full article

Herein, raw and alkali-treated hydrochars from biomass waste are prepared as a highly active catalyst for the conversion of waste motor oil into diesel-like fuels. Among all materials, hydrochar obtained at 250 °C and subsequent alkali activation with KOH showed a 600% improvement of the kinetic constant from 0.0088 to 0.0614 m⁻¹. Conversion values at the same conditions were also improved from 66 to 80% regarding thermal and catalytic cracking, respectively. Moreover, the activation energy was also reduced from 293 to 246 kJ mol⁻¹ for thermal and catalytic cracking, respectively. After characterization, the enhanced catalytic activity was correlated to an increased surface area and functionalization due to the alkali activation. Finally, the liquid product characterization demonstrated that catalytic cracking is more effective than thermal cracking for producing hydrocarbons in the diesel range. In particular, hydrochar-based catalysts are suggested to promote the formation of specific hydrocarbons so that the carbon distribution can be tailored by modifying the hydrothermal treatment temperature. Full article

The valorization technique successfully transformed waste polyethylene terephthalate (PET) into valuable carbon nanomaterial (CN)/graphene, while doped and undoped ZnO nanopowders were synthesized via sol–gel methods. Utilizing XRD, BET, TEM, EDX, FTIR, and TGA analyses, the synthesis of sp² 2D sheet, pristine, and doped ZnO nanostructures was confirmed. Solid-state gas sensor devices, tested under 51% relative humidity (RH), 30 °C ambient temperature, and 0.2 flow rate, exhibited a 3.4% enhanced response to H₂ gas compared to CO₂ at 50 ppm concentrations over time. Notably, the ZnO/CN sensor surpassed CN and ZnO alone, attributed to CN dopant integration with decreasing order of response performance as ZnO/CN > CN > ZnO. This study underscores the efficacy of valorization techniques in generating high-value carbon nanomaterials and their efficacy in bolstering gas sensor performance, with ZnO/CN demonstrating superior response capabilities. Full article

This review article gathers the most recent recycling technologies for thermoset and thermoplastic polymers. Results about existing experimental procedures and their effectiveness are presented. For thermoset polymers, the review focuses mainly on fibre-reinforced polymer composites, with an emphasis on epoxy-based systems and carbon/glass fibres as reinforcement, due to the environmental concerns of their end-of-life management. Thermal processes (fluidised bed, pyrolysis) and chemical processes (different types of solvolysis) are discussed. The most recent combined processes (microwave, steam, and ultrasonic assisted techniques) and extraordinary recycling attempts (electrochemical, biological, and with ionic liquids) are analysed. Mechanical recycling that leads to the downgrading of materials is excluded. Insights are also given for the upcycling methodologies that have been implemented until now for the reuse of fibres. As for thermoplastic polymers, the most state-of-the-art recycling approach for the most common polymer matrices is presented, together with the appropriate additivation for matrix upcycling. Mechanical, chemical, and enzymatic recycling processes are described, among others. The use of fibre-reinforced thermoplastic composites is quite new, and thus, the most recent achievements are presented. With all of the above information, this extensive review can serve as a guide for educational purposes, targeting students and technicians in polymers recycling. Full article

This work presents the research results on the development of an innovative, hydrometallurgical technology for the production of manganese(II) perrhenate dihydrate from recycled waste. These wastes are scraps of Ni-based superalloys containing Re and scraps of Li–ion batteries containing Mn—specifically, solutions from the leaching of black mass. This work presents the conditions for the production of Mn(ReO₄)₂·2H₂O. Thus, to obtain Mn(ReO₄)₂·2H₂O, manganese(II) oxide was used, precipitated from the solutions obtained after the leaching of black mass from Li–ion batteries scrap and purified from Cu, Fe and Al (pH = 5.2). MnO₂ precipitation was carried out at a temperature < 50 °C for 30 min using a stoichiometric amount of KMnO₄ in the presence of H₂O₂. MnO₂ precipitated in this way was purified using a 20% H₂SO₄ solution and then H₂O. Purified MnO₂ was then added alternately with a 30% H₂O₂ solution to an aqueous HReO₄ solution. The reaction was conducted at room temperature for 30 min to obtain a pH of 6–7. Mn(ReO₄)₂·2H₂O precipitated by evaporating the solution to dryness was purified by recrystallization from H₂O with the addition of H₂O₂ at least twice. Purified Mn(ReO₄)₂·2H₂O was dried at a temperature of 100–110 °C. Using the described procedure, Mn(ReO₄)₂·2H₂O was obtained with a purity of >99.0%. This technology is an example of the green transformation method, taking into account the 6R principles. Full article

Composting is a waste management practice that converts organic waste into a product that can be used safely and beneficially as a bio-fertiliser and soil amendment. Non-methane volatile organic compounds (NMVOCs) from composting are known to cause damage to human health and the environment. The impact of waste management on the environment and workers is recognised as a growing environmental and public health concern. Measurements of NMVOCs emitted during composting have been carried out only in a few studies. NMVOC emissions are typically reported as a group rather than as species or speciation profiles. Recognising the need to investigate the issues associated with NMVOCs, the objective of this study is to estimate variation in life cycle assessment (LCA) results when NMVOCs are considered individual emissions compared to grouped emissions and to compare midpoint and endpoint life cycle impact assessment (LCIA) methods. In general, the ReCiPe 2016 LCIA method estimated the highest impact from the composting process in comparison to IMPACT World+ and EF 3.0 for the impact categories of ozone formation, stratospheric ozone depletion, and particulate matter formation. For ReCiPe 2016 and IMPACT World+, the NMVOC emissions were not linked to human toxicity characterisation factors, meaning that the contribution from NMVOC towards human health risks in and around composting facilities could be underestimated. Using individual NMVOCs helps to additionally estimate the impacts of composting on freshwater ecotoxicity and human carcinogenic and non-carcinogenic toxicity potential. If ecotoxicity or toxicity issues are indicated, then LCA should be accompanied by suitable risk assessment measures for the respective life cycle stage. Full article

This study focuses on recycling Shammi corn stalks in the cement industries, further avoiding air and soil pollution caused by their improper disposal. This crop residue was thermally treated at 700 °C for 2 h under an oxygen-rich environment to produce Shammi corn stalk ash (SCSA). This SCSA was used as a cement replacement material (2–10%, w/w), whereas the control sample included only cement. The compressive strength values for the 4% (w/w) replacement ratio at 2-, 7-, and 28-day ages were greater than those for the control by 26.5%, 15.8%, and 11.4%, respectively. This 4% (w/w) also maintained a better flexural strength than other mixtures, with proper initial and final setting times (135 and 190 min), workability (18.5 cm), and water consistency (27.5%). These mechanical/physical properties were integrated with socio-enviro-economic data collected from experts through a pairwise comparison questionnaire, forming the inputs of a multi-criteria decision-making (MCDM) model. Recycling SCSA in the cement-manufacturing process attained positive scores in the achievement of the three pillars of sustainable development, revealing an overall score greater than the control. Hence, the study outcomes could be essential in developing green concrete, cement blocks, and mortar, based on the sustainable development goals (SDGs) agenda. Full article

This research highlights the importance of addressing bioplastic contamination in recycling processes to ensure the quality of recycled material and move towards a more sustainable circular economy. Polyethylene (PE) is a conventional plastic commonly used in packaging for which large amounts of waste are produced; therefore, PE is generally recycled and has an established recycling process. However, the contamination of biodegradable polymers in the PE waste stream could impact recycling. This study, therefore, focuses on polyethylene (PE) that has been polluted with a commercial thermoplastic starch polymer (TPS), as both materials are used to produce plastic films and bags, so cross-contamination is very likely to occur in waste separation. To achieve this, recycled PE was blended with small quantities of the commercial TPS and processed through melt extrusion and injection molding, and it was further characterized. The results indicate that the PE-TPS blend lacks miscibility, evidenced by deteriorated microstructure and mechanical properties. In addition, the presence of the commercial TPS affects the thermal stability, oxidation, and color of the recycled PE. Full article

Dumped non-biodegradable tires present a significant environmental threat, with overflowing landfills and associated health risks highlighting the urgency of tire waste disposal. Current disposal methods, such as stacking tires in open spaces, exacerbate the problem. The large-scale recycling of tire rubber waste offers environmental benefits. This study examines the effects of pre-treatment using NaOH and micro-silica as a mineral admixture on the mechanical strength of crumb rubber concrete (CRC) with partial replacement of natural sand. Samples of M20 and M30 grade were prepared with varying levels of crumb rubber (CR) replacement and evaluated at 28 days. CRC prepared with pre-treated NaOH solution and micro-silica showed improved workability and strength compared to conventional concrete and untreated CRC, with the highest strength observed for 5% CR replacement using micro-silica. Predictive models and micro-structural analysis validated these findings. Life Cycle Assessment (LCA) using OpenLCA v2.10 software and the ecoinvent database revealed that incorporating micro-silica into CRC did not significantly increase environmental impacts, compared to conventional concrete across different mixes. Full article